BS 5053-1985 金属丝绳用缆索和吊索及纤维芯线的试验方法
作者:标准资料网 时间:2024-04-29 06:33:57 浏览:8748
来源:标准资料网
【英文标准名称】:Methodsoftestforcordageandwebbingslingsandforfibrecoresforwireropes
【原文标准名称】:金属丝绳用缆索和吊索及纤维芯线的试验方法
【标准号】:BS5053-1985
【标准状态】:作废
【国别】:英国
【发布日期】:1985-08-30
【实施或试行日期】:
【发布单位】:英国标准学会(BSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:W58
【国际标准分类号】:
【页数】:24P;A4
【正文语种】:英语
Product Code:SAE J1850
Title:Class B Data Communications Network Interface
Issuing Committee:Vehicle Architecture For Data Communications Standards
Scope:This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers.This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.Although devices may be constructed that can be configured to operate in either of the two primary implementations defined herein, it is expected that most manufacturers will focus specifically on either the 10.4 Kbps implementation or the 41.6 Kbps implementation depending on their specific application and corporate philosophy toward network usage. However, low-volume users of network-interface devices are expected to find it more effective to use a generic interface capable of handling either of the primary implementations specified in this document.
基本信息
| 标准名称： | 管路压力试验要求 |
| 中标分类： |
船舶 >>
船舶管路附件 >>
船舶管路附件综合 |
| ICS分类： |
造船和海上建筑物 >>
船舶和海上建筑物综合 >>
管路系统
|
| 替代情况： | 部分被CB/T 250-2008代替 |
| 发布部门： | 中国船舶工业总公司 |
| 发布日期： | 1994-04-11 |
| 实施日期： | 1994-10-01 |
| 首发日期： | 1900-01-01 |
| 作废日期： | 1900-01-01 |
| 提出单位： | 中国船舶工业总公司 |
| 归口单位： | 中国船舶工业总公司六○三所 |
| 起草单位： | 求新造船厂 |
| 起草人： | 戴维东、潘雪英 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 1994-10-01 |
| 页数： | 4页 |
适用范围
本标准规定了船舶动力管路和船舶系统管路压力试验要求。
本标准适用于船舶动力管路和船舶系统管路。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 船舶 船舶管路附件 船舶管路附件综合 造船和海上建筑物 船舶和海上建筑物综合 管路系统
